How to use dhclient?

unicorn

I want to use dhclient to connect to internet,but dhclient can't be found.How can I use dhclient?

MG_

It's called dhcpcd, not to be confused with dhcpd.

unicorn

How to connect to internet then?

MG_

If ping www.google.com replies, you are connected. Does dhcpcd give you a ip and gateway?

unicorn

How to use dhcpd to connect to internet?

Jay

unicorn check this out https://archive.unitedbsd.com/t/netbsd-desktop-pt-2-set-up-wireless-networking-on-netbsd-with-wpa-supplicant-and-dhcpcd/281

unicorn

I connect internet through my phone's usb network share.I want to use dhclient.
Ifconfig only shows re0,lo0 and my phone's.

MG_

unicorn USB-tethering... Never tried that, only Android's wifi-hotspot function. I think you need at least a kernel module for a usb ethernet device. What says dmesg after you plug in the USB cable? It must see some hardware on the USB...

unicorn

ifconfig shows urndis0.I want to use dhclient urndis0 connect to internet

jmmarin

It usually appears as urndis0.
If as unicorn says it appear with ifconfig, a mere "sudo ifconfig urndis0 up " and "sudo service dhcpcd restart" should be enough.
If that works, edit rc.conf accordingly.

unicorn

It works,thanks.I had just install firefox,but Chinese fonts can't display properly.Which package should I install?

jmmarin

unicorn Package noto-ttf has support for Asian languages. Once installed, look into the message that appears about changing your Xorg config in order Firefox can use it.

unicorn

nice,it works.All fonts display properly.

unicorn

how to adjust sound volume?I use earphone but I cannot hear sound in my earphone,instead sound played in the air.

nia

unicorn To use your headphones, if they are connected over 3.5mm jack, you may need to use mixerctl to change the DAC, see http://netbsd.org/docs/guide/en/chap-audio.html#chap-audio-hdaudio - aiomixer can also do this "graphically" if you install it.

If they are connected over USB, you need to change the default audio device with audiocfg, also described in the guide http://netbsd.org/docs/guide/en/chap-audio.html#chap-audio-configuring-device

MG_

unicorn I see that sysctl setting hw.snd.default_unit exists. Didn't try it yet, but in FreeBSD it's used to choose the audio output line you are using. Many computers can choose front jack, rear jack or internal speaker. Try 1, 2, 3... All accepted numbers.

unicorn

nia

I use this command but failed:

mixerctl -w outputs.dacsel=ADC02
mixerctl: Bad set value ADC02.

ADC03 is the same

rvp

unicorn I use this command but failed:

mixerctl -w outputs.dacsel=ADC02
mixerctl: Bad set value ADC02.

It will fail because you're trying to set the output to be a microphone (ADC = analog-to-dIgital converter. You want DAC: digital-to-analog)

Post the output of these commands:

mixerctl -av
hdaudioctl list
hdaudioctl show n1 n2

The hdaudioctl commands will have to be run as root. The n1 and n2 values for the show command you can get from the list output. No need to do a show on the HDMI device.

unicorn

in /var/run/dmesg.boot shows

hdafg0: DAC00 2ch: HP Out [Jack]
hdafg0: ADC02 2ch: Mic In [Built-In]
hdafg0: ADC03 2ch: Mic In [Jack}

unicorn

mixerctl outputs:

inputs.dac=192,192 volume delta=3
inputs.reclvl=72,72 volume delta=8
inputs.reclvl.mute=on  [ off on ]
inputs.reclvl2=72,72 volume delta=8
inputs.reclvl2.mute=on  [ off on ]
inputs.record=184,184 volume delta=8
inputs.record.mute=on  [ off on ]
inputs.record2=184,184 volume delta=8
inputs.record2.mute=on  [ off on ]
inputs.beep=184,184 volume delta=8
inputs.beep.mute=off  [ off on ]
inputs.beep2=184,184 volume delta=8
inputs.beep2.mute=off  [ off on ]
inputs.record3=184,184 volume delta=8
inputs.record3.mute=off  [ off on ]
inputs.dac2=0,0 volume delta=256
inputs.dac2.mute=off  [ off on ]
inputs.record4=0,0 volume delta=256
inputs.record4.mute=off  [ off on ]
record.mic=0,0 volume delta=64
record.monitor=0,0 volume delta=64
outputs.master=0,0 volume delta=256
outputs.master.mute=off  [ off on ]
record.mic2=0,0 volume delta=256
record.mic2.mute=on  [ off on ]
inputs.beep3=0,0 volume delta=256
inputs.beep3.mute=off  [ off on ]
inputs.beep4=0,0 volume delta=256
inputs.beep4.mute=off  [ off on ]
inputs.record5=0,0 volume delta=256
inputs.record5.mute=off  [ off on ]
inputs.reclvl3=0,0 volume delta=256
inputs.reclvl3.mute=on  [ off on ]
inputs.beep5=0,0 volume delta=256
inputs.beep5.mute=off  [ off on ]
inputs.beep6=0,0 volume delta=256
inputs.beep6.mute=off  [ off on ]
inputs.record6=0,0 volume delta=256
inputs.record6.mute=off  [ off on ]
outputs.dacsel=DAC00  { DAC00 }
record.source=ADC02,ADC03  { ADC02 ADC03 }

hdaudioctl list outputs:

codecid 0x00 nid 0x01 vendor 0x10EC product 0x0662 subsystem 0x1E208086 device hdafg0
codecid 0x03 nid 0x01 vendor 0x8086 product 0x2806 subsystem 0x1E208086 device hdafg1

the third command outputs:

Operation not supported by device

rvp

unicorn the third command outputs:

Operation not supported by device

You have to do:

hdaudioctl show 0 1

Also post the output of:

audiocfg list